ADD: No.28 Tianshan Road, Xinbei District, Changzhou, Jiangsu Province, China
Nema 51 Step Motor Driver
This nema 51 step motor driver with lower noise, high accuracy, high efficiency and short circuit, comes from us which is one of the leading manufacturers and suppliers in this field. Having been well exported to the United States, Germany, Russia, etc, our equipment you buy is at cheap price.
The input signal terminal of the driver uses a pluggable terminal, which can be unplugged first, and then plugged in. The input signal of this driver adopts double-ended interface, which can meet various interface forms.
This nema 51 step motor driver allows you to operate independently, coordinate remote diagnostics and parameter settings, pass motion parameters and forward and reverse signals. This drive is absolutely safe to drive. Its current and standby current can be digitally selected. Some motion parameters use sensorless lost motion detection techniques or reference switches.
1.Using new digital sinusoidal micro-segmentation algorithm
2.Support single / dual control pulse input
3.A test run function, power failure, phase memory function
4.Positioning accuracy, low noise, small temperature rise, high efficiency
5.Simple high-performance, multi-function, operation, cost-effective
6.With short circuit, overvoltage, undervoltage, overtemperature protection and improving functions
7.Motor parameters automatically adapt to the function to ensure maximum play all types of motor function
Input Power supply:
PWM constant current chopping, two phase Sine wave output current
Suitable stepper motor
85，86，110,130 series two phase stepper motor
-10℃～55℃ 15～85%RH、No condensation. Non-corrosive, flammable, explosive, conductive gas, liquid and dust
－40℃～+55℃, ＜93%RH，No condensation, no frost
Microstep subdivision setting :
Users can set the driver Microstep by the SW1-SW5 five switches, total 28 micro-step. When you set the microstep , pls stop the driver working. The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure .
Output current setting
Users can set the driver Microstep by the SW1-SW5 five switches. The setting of the specific Microstep subdivision, please refer to the instructions of the driver panel figure..
Double pulse setting
SW7 sets pulse mode, setting “on'' as double pulse mode, setting off'' as pulse + direction mode.，CW+/CW is Clockwise ，CCW+/CCW- is Counterclockwise, need to confirm the wire of stepper motor 。
Automatic half current function
Users can set the driver half flow function by SW6. "OFF" indicates the quiescent current is set to half of the dynamic current, that is to say, 0.5 seconds after the cessation of the pulse, current reduce to about half automatically. "ON" indicates the quiescent current and the dynamic current are the same. User can set SW6 to "OFF", in order to reduce motor and driver heating and improve reliability.
Self test function
When SW1-SW5 is OFF , Inner of drive send 1K pulse to test whether the motor，wire，and self is normal.
PUL+ and PUL- are the positive and negative side of control pulse signal; DIR+ and DIR- are the positive and negative side of direction signal; ENA+ and ENA- are the positive and negative side of enable signal .
A+ and A- are connected to a phase winding of motor; B+ and B- are connected to another phase winding of motor. If you need to backward, one of the phase windings can be reversed .
It uses DC power supply，recommended working voltage is 110－220VAC，power is over 500W，voltage shouldn't be over 230VAC and below 110VAC.
There are two indicator lights. Power indicator is green. When the driver power on, the green light will always be lit. Fault indicator is red, when there is over-voltage or over-current fault, the red light will always be lit; after the driver fault is cleared, if re-power the red light will be off.
The size of motor driver is 180X76X130 mm，mounting holes is 185mm. Chest and upright installation are ok，we suggest upright installation. During installation, it should be close to the metal cabinet for heat dissipation.
signal interface and sequence in time :
Inner electric circuit:
Connection of Output alarm:
Note : OC is output of photoelectric isolation , Max voltage capability is 30VDC ,maximum saturation current is 100 MA motor driver .
Output optocoupler is not conducted under the normal working condition .
Interface connection and installing dimension: